369X is the removable brass seat that Danco's #18 replaces in Sterling compression faucets. Catalogs list it at 1/2 in. x 24 thread, 3/8 in. tall and 9/16 in. across. Danco lists the same seat for Royal Brass 9649 and American Kitchen faucets.
Schematic, not to scale. It shows only the features named on this page. No bench photo of this part yet.
Specifications
OEM number
Sterling 369X, per Danco's #18 listing. No Sterling document found
Also listed for
Royal Brass 9649; American Kitchen (no number given)
Type
Removable threaded brass seat (bibb seat) for compression stems
Thread
1/2 in. x 24 threads per inch
Height
3/8 in., per Danco's #18 listing; Jones Stephens titles B40015 1/2 in. x 24 x 3/8 in.
Widest point
9/16 in. outside diameter, per Danco's #18 listing
The Sterling seat number Danco prints as replaced by its #18 seat (30017V and 30017E). Danco gives it as 1/2 in. x 24, 9/16 in. O.D., 3/8 in. tall.
9649
Royal Brass
Listed in the same Danco #18 text as a Royal Brass number the seat replaces.
Where it goes
Danco's #18 text at HD Supply and Trayco lists the seat for Sterling, Royal Brass and American Kitchen faucets. No Sterling document was found that names a faucet or valve model.
One hardware store lists a Danco stem made for seat model No. 18 for Sterling tub and shower faucet series 104, 124, 134 and 144. That listing is for the stem, not the seat.
True Value sells LASCO's 1/2 in. x 24 Sterling seat as a lavatory seat, and Zoro lists Thrifco's X-26 Sterling seat for lavatory faucets.
Confirm it is your part
The seat is a short brass insert threaded into the valve pocket under the stem, with a wrench opening through the center. If the old part is a rubber seat on a spring, stop: different Sterling part.
Measure across the threads. This seat reads 1/2 in.
Count the threads with a pitch gauge. This seat is 24 per inch. If the gauge reads 20, stop: the old part is a 1/2 in. x 20 seat such as Pfister 970-510, not a 369X.
Measure the height with calipers. Catalogs give 3/8 in. A 15/32 in. seat is the Central Brass 263-B; an 11/32 in. seat is the Streamway 108-25.
Measure the widest point. Danco gives 9/16 in. A 5/8 in. reading points to the Central Brass seat, a 1/2 in. reading to the Streamway seat.
Look-alikes
Pfister 970-510 seat (1/2 in. x 20)
Why it gets confusedSame 1/2 in. thread diameter, and Pfister's drawing prints the same 9/16 in. and 3/8 in. figures.
How to tellThread pitch is the only tell. Pfister sells the 970-510 as 1/2 in. x 20; Danco lists the #18 for 369X at 24 threads. Check it with a pitch gauge, not calipers.
Central Brass 263-B seat (Danco #7)
Why it gets confusedSame 1/2 in. x 24 thread, sold on the same seat cards.
How to tellDanco's Central seat is listed at 15/32 in. tall and 5/8 in. across. The 369X is 3/8 in. tall and 9/16 in. across.
Streamway 108-25 seat (Danco 30078E)
Why it gets confusedSame 1/2 in. x 24 thread, also sold as a universal seat.
How to tellListed at 11/32 in. tall and 1/2 in. across, so the widest point is no bigger than the thread. The 369X has a 9/16 in. collar over a 1/2 in. thread.
Sterling single-handle seats and springs, A01408 (Danco 88745)
Why it gets confusedSold under Sterling with 1/2 in.-24 in the title.
How to tellA rubber seat on a stainless spring for Sterling single-handle models 021 to 026. It is not a threaded brass insert and takes no seat wrench.
Cross-reference numbers
Numbers other makers and sellers list against this part. The notes say how far each one goes.
Maker
Number
Note
Danco
#18 / 30017E
2 per pack; Zoro's page names 369X and 9649
Danco
#18 / 30017V
2 per pack; HD Supply and Trayco pages name 369X and 9649
Not printed on this page
Where the sources disagree, the figure is left off until it is settled.
A Sterling parts document for 369X. None was found; the number comes from Danco's #18 text, and no faucet model is printed for it.
LASCO SB-26NL, BrassCraft SCB1719X, Jones Stephens B40015 and Thrifco X-26. Each is sold as a 1/2 in. x 24 Sterling seat, but no page opened names 369X.
Larsen X-26PNL and S99S0369. No outside page was found that ties either number to this seat.
Wrench opening shape. No outside source states it. Try the seat wrench in the old seat.
Hot side versus cold side. No source says whether one seat serves both sides.
Field notes
Danco's 9/16 in. by 3/8 in. figures for this seat are the same figures Pfister's drawing prints for the 1/2 in. x 20 970-510. Calipers will not separate the two. A pitch gauge will.
FourHome replacement
The FourHome replacement for Sterling 369X ships as ten brass seats with a 1/2 in. x 24 thread; a seat wrench, stem washers and thread sealant are not in the pack.
Catalogs disagree now and then, and makers revise parts without changing the number. Compare the old part before buying. Identify by measurement lists every indexed part near a given length and spline count.