Repair kit for Pfister 910-374 and 910-013 hot and cold stems
This is the wear-parts kit for one Pfister hot or cold compression stem, not the stem. BrassCraft lists the same seat, bibb washer, screw and bonnet packing for 910-374 and 910-013. The cap thread gasket number is the one piece that changes between them.
Schematic, not to scale: the 910-374 stem this kit services, labelled with where the kit parts go. The kit has no stem. The lower end is left blank because no source gives the tip. No bench photo of this kit yet.
Specifications
Services
Pfister 910-374 (910-3740) and 910-013 (910-0130) hot and cold compression stems
OEM kit number
None found in a Pfister document
Type
Seat and seal kit for a brass compression stem, side handle. No stem in it.
Seat thread
21/32 in. x 18. Pfister lists seat 970-5000 for 910-374 (spec sheet) and 970-500 for 910-013 (Bedford parts explosion).
Pfister's spec sheet calls 910-374 a shower stem for compression multi-handle valves and says to order seat 970-5000 separately. Pfister's Bedford 801-WS-BD parts explosion shows 910-013 with seat 970-500.
BrassCraft's SP-0341 catalog files ST5326 against 910-374 and ST2874 against 910-013 and lists the seat, washer, screw, packing and cap thread gasket as separate service parts. Those are the five pieces this kit renews.
Home Depot lists the Pfister 910-013 stem as compatible with 2 and 3-handle Crown Imperial faucets.
Confirm it is your part
Position. The stem came from behind the left or right handle. A stem from the center handle of three is a diverter and takes a different kit.
Seat. The old seat should thread 21/32 in. x 18, the 970-500 size. A seat that is smaller across or has finer threads belongs to another kit. Set the old seat beside the new one before it goes in.
Stem class. BrassCraft puts 910-374 in length class 12 and 910-013 in class 9. Either stem takes this kit; the class only tells which stem you hold.
Cap thread gasket. BrassCraft numbers it SC0198 on 910-374 and SC0191 on 910-013. The kit has one, listed at 1 in. x 7/8 in. x 1/16 in. Lay the old gasket on it.
Stem. The kit has no stem, bonnet or broach. Stripped stem threads, a rounded broach or a bent stem mean the job needs the stem, not this kit.
Look-alikes
FourHome 10 piece diverter kit for Pfister 910-382
Why it gets confusedSame brand, same three-handle valve, sold next to this kit.
How to tellIt is for the center diverter. BrassCraft gives 910-382 cap thread gasket SC0262, not SC0198 or SC0191. That kit is 10 pieces and carries a nylon diverter washer. This one is 5 pieces.
Pfister 910-374 stem
Why it gets confusedSame number in both titles, and FourHome sells both.
How to tellThe stem is the brass part with the 12-point broach and the smooth bonnet. The kit is five loose pieces with no stem. The stem has its own record.
Danco 124162 hot and cold stem repair kit
Why it gets confusedCarded as a hot and cold stem repair kit for Price Pfister tub and shower faucets.
How to tellCarded by Danco stem ID, not Pfister number: 9H-1, 9H-2, 10I-7, 10I-8, 10I-9, 12H-1, 12H-2, 12H-3. Home Depot ties Danco 12H-2H/C to 910-374 on a separate page. No page opened lists the 124162 seat size.
Everbilt 865750 stem repair kit
Why it gets confusedAlso a 5 piece kit for Pfister hot and cold stems.
How to tellHome Depot names no Pfister part number and describes O-rings and rubber seals without listing the pieces, so it cannot be matched to this kit piece by piece.
Lasco 0-2011 tub and shower stem kit
Why it gets confusedTitled a Price Pfister tub and shower stem repair kit with seat.
How to tellDK Hardware lists 1 each 3/8L flat washer, packing, friction washer and brass screw, with no seat despite the title, and names no Pfister part number.
Not printed on this page
Where the sources disagree, the figure is left off until it is settled.
Everbilt 865750, Lasco 0-2011 and Danco 124162 as cross-references. None of their pages names 910-374 or 910-013.
Whether the one cap thread gasket fits both stems. BrassCraft gives 910-374 and 910-013 different gasket numbers and no source opened gives both sizes.
Danco 124162 seat thread. No page opened for that kit prints its seat size.
Stem length in inches. Pfister's drawing and the BrassCraft catalog print different figures for 910-374, so only the gauge class is given.
A Pfister kit number. No Pfister document opened lists a repair kit for 910-374 or 910-013.
Field notes
BrassCraft lists the same seat, bibb washer, screw and bonnet packing for 910-374, 910-013 and the 910-382 diverter. The cap thread gasket is the piece that ties a kit to one stem.
FourHome replacement
The FourHome kit ships 5 pieces for one stem: a brass bibb seat, 21/32 in. x 18, with a seat wrench socket; an 11/16 in. flat stem washer; a 3/8 in. x 10-24 brass washer screw; a 1 in. x 7/8 in. x 1/16 in. cap thread gasket; and a 3/4 in. x 3/8 in. x 1/4 in. bonnet packing; no stem, handle or grease.
If the stem itself is worn, the Pfister 910-374 stem record covers the stem, and its look-alikes section links the 910-382 vs 910-374 comparison for telling the side stems from the center diverter.
FourHome replacement
Replacement Stem Repair Kit for Pfister 910-374 and 910-013, 5 Pc
Application
Five pieces for one 910-374 or 910-013 hot or cold stem; no stem
Catalogs disagree now and then, and makers revise parts without changing the number. Compare the old part before buying. Identify by measurement lists every indexed part near a given length and spline count.